Hyosung All Motorcycles in Leeds

Genuine Chain Adjuster PLATES  taken from GT125RC - 2k miles old. You are getting 2 plates (pair) -  the plates are "dirty" from dry chain grease but will clean up  once washed off.  it has old black paint on it There is some rust in areas and will need a good lick of VHT paint! Thanks for looking!

Genuine Chain Adjuster PLATES  taken from GT125RC - 2k miles old. You are getting 2 plates (pair) -  the plates are "dirty" from dry chain grease but will clean up  once washed off. There is some rust in areas and will need a good lick of VHT paint!

CLUTCH PLATES REMOVED FROM RUNNING GV250 ENGINE ?? They are around 2.9mm thickness  (OEM limit is 2.6mm) ?  PLATES ARE 100% working OK. NO CRACKS. ?

Genuine ROCKER Cover GASKETS x1   *(ONE PIECE)* ? Removed From Seized GT125R Carby Engines THE GASKET is NOT TESTED. I DO NOT KNOW IF THIS GASKET LEAKS OR NOT  BUT THEY SEEM TO LOOK OKAY "FROM MY EYES"  PLEASE NOTE IT IS SOLD AS "SPARES/REPAIRS/UNTESTED PARTS"  ?

Hyosung Speedo Drive removed from carb model GV125 2005. This unit is not tested , because the donor bike had a seized engine , so we did not get a chance to ride it and test  the speedo drive. So it is sold as "Spares & Repairs" due to not being Tested.

Genuine oil cooler COVER GRILL  taken from a GV125C 2015 Aquila under 5,000 miles. ?CHROME HAS SCRATCHES AND OLD STONE CHIPPINGS ?NO CRACKS.   READY TO FIT. "ENGINE COOLER" NOT INCLUDED YOU ARE ONLY GETTING A GRILL / MESH COVER!

Oil Filter cover removed from GV250 2011 ? In working order ? SPRING & O-RING NOT INCLUDED.   SCREWS NOT INCLUDED.  ?

SWING ARM SHAFT BAR  taken from GT125 ?In working condition.   ?Check pictures.  ? There is surface rust and general wear/tear on it. ?This will fit on the FRAME of  GT250 (Carb & EFi)  and also Carb Models of GT125 & GT125R  All the GT/GTR 125cc & 250cc bikes from 2003 to 2019 #Guaranteed ?

Headlight or Fuel Pump Relay – Hyosung GT125R GT250R GV250 ST7 GT650 GV650 This new relay is for restoring life in your hyosung’s head lights or the electric fuel pump in some EFi models.  Hyosung uses the same BLUE or BLACK relay across many models of their bikes. Rest assured the aftermarket relay sold on HyoRiders Shop is a direct fitment too.  Restores the EFi fuel pump Electric  Injection EFi bikes need relays for the fuel pumps to work.

HYOSUNG Frame Rail removed 2008 GT250 ✔ Ready to fit  📷 Frame rail has rust spots so it is a good idea to repaint it! 👋 Sold as cheap clearance. We don't want it anymore.  ❗ Fits GT125 GT250 GT125R GT250R Frames.

GENUINE HYOSUNG FRONT BRAKE HOSE REMOVED FROM GT250R 2009 It is GENUINE and 2000 miles old. Please read below , before buying. There will be no returns.  #clearance.

You're looking at a 2016 ENGINE removed from GT125RC ,  8000 miles old. Please read below before buying, as it is spares and repairs with missing parts too. ?

CHAIN GUARD & SWINGARM TAKEN FROM GV125C 2005 ?? CHAIN GUARD SCREWS ARE VERY RUSTY AND STUCK! WE WILL NOT ATTEMPT TO REMOVE IT AS THE CHAIN GUARD IS A RARE PIECE OF PLASTIC TO ACQUIRE NOWDAYS SORRY!

Genuine handlebar removed from GV125 2002  (22mm thick GENUINE KOREA HYOSUNG) (7/8"Inch=22mm) ? Fits only 22mm throttle grips and switch gears ? Compatible with : GV125 Carb Models 2002 to 2017 ?

??? needs SERIOUS repair. please see pictures before buying!

Rear Master Cylinder removed from GT125RC 2016 Model See details below before buying! It is spares & repairs , because it is JAMMED (it was previously working,  now it is stuck!)  So it will need to be UNJAMMED , then it will work. Part numbers = 69609HN9100, 69609HN9101, 69609HP9502, 69609HP9503 Brake Master cylinder have some scratches on it, so it will need repaint / refurbish to make it look pretty again!

Rear Brake Pedal removed from GT250N EFi  ? THIS ITEM WORKS 100% ? See pictures before buying.

RED FRONT LOWER CHIN COWLING that was removed  from a 2017 GT125R Bike VERY GOOD PAINT?.  ORIGINAL RED HYOSUNG COLOUR. ? ?

You're looking at a genuine regulator removed from GV125C 2016 that only had 6,000 miles It is ? working & shows 14.3-14.8V on testing it on our donor bike. It will need some cleaning because regulators are fitted on the rear, so the dirty roads spoiled it a little bit.

You are looking at a Genuine  ADAPTER that converts any 51mm PIPE (Black Widow or Hyosung OEM Pipe) to accept 4-bolt cans from  hawk, scorpion , MTC, 2Bros,   or OEM Hyosung Cans    (Cans is UK english language for Silencers/Mufflers if you're from USA!) This unit is brand new and Black Widow UK makes them.  FULLY 100% STAINLESS STEEL. Who likes rust? Black widow themselves will charge you GBP60 for it brand new We are selling ours cheaper ?  (If Black widow drops the price, so will we)  ??

 REAR INTAKE MANIFOLD FOR GT250/GT250R CARBY ? THIS MANIFOLD IS REMOVED FROM GT250 ?  NO AIR LEAKS WERE FOUND WHEN TESTING ?  IT IS 100% WORKING, GUARANTEED.  ??  It has paint marks on it, but does not affect operation ? It will need a clean and FRESH O-RING ?  SEE PICTURES.  IT IS SHOWING IT'S AGE ;-) ??

FRONT INTAKE MANIFOLD REMOVED FROM GT250 carby ? Working OK! - the rubber is good!

FRONT INTAKE MANIFOLD REMOVED FROM GT250 carby ? Working OK! - the rubber is good!

You are looking at OEM (Genuine) FRONT & REAR EXHAUST PIPES removed from 2016 GT125RC The pipes have approximately aged 10,000 miles and only fits 51mm silencers (end cans) Please note below: IT IS REALLY IMPORTANT YOU MUST READ THE DESCRIPTION BELOW! 📷 Inspect pictures please, there is bits of rust in places. It will need repaint in VHT black I will need 1-2 days to pack this item before dispatch.

You are looking at OEM (Genuine) FRONT & REAR EXHAUST PIPES removed from 2016 GT125RC The pipes have genuinely aged 2,000 miles and has the original silver silcencer included. 100% working, no leaks , no blowing , it is ready to go.? Please note below: IT IS REALLY IMPORTANT YOU MUST READ THE DESCRIPTION BELOW!